CultureWorld Tech Rankings & Curiosities

How Undersea Internet Cables Carry the World's Data

Undersea internet cables send light through glass fibers between continents. Ships lay protected cables and recover damaged sections for repair.

How do undersea internet cables work?

Undersea internet cables carry data as light through thin glass fibers laid across the seabed. Equipment at coastal landing stations sends and receives the optical signals, while underwater amplifiers support long routes. These cables connect national and regional networks into the physical backbone of international communications.

A phone can begin its journey wirelessly, but that does not make the whole route wireless. Beyond the local network, data can travel through terrestrial fiber and an ocean cable before reaching another continent.

How many submarine cables are there?

TeleGeography’s FAQ, checked in November 2026, says it tracks more than 600 active and planned cable systems. It estimates more than 1.5 million kilometers of submarine cable in service as of early 2026.

The count and length use different scopes: the system count includes planned projects, while the length estimate concerns cable already in service. They should not be combined into an average as if they described an identical inventory.

The International Cable Protection Committee separately reports approximately 500 systems and around 1.8 million kilometers. Published length estimates therefore span more than 1.5 million to about 1.8 million kilometers, with dates and inventory definitions affecting comparison.

These are estimates of a changing network, rather than a permanent exact total. New systems enter service while older ones are retired, and one named system can contain several branches and landings.

What is inside an undersea cable?

Part What it does
Optical fibers Carry the information as light
Strength members Help the cable withstand handling and mechanical tension
Electrical conductor Supplies power to underwater equipment in powered systems
Insulating and protective layers Separate components and help resist the marine environment
Additional armor where needed Adds protection in vulnerable sections
Repeaters and branching units Amplify signals or connect sections to different destinations

The fiber is only a small part of the complete structure. A cable also needs to survive manufacture, loading, deployment and possible recovery for repair.

Protection changes with the environment. Heavy armor adds strength but also weight, so the construction chosen for a vulnerable coastal section can differ from a deep-ocean section.

Unlike a familiar charging lead, this is an engineered system with different optical, electrical and mechanical functions. Our guide to USB cable types explains another example of why a cable’s outer appearance does not describe everything it does.

How can light carry so much information?

The transmitting equipment encodes information onto optical signals. The receiving equipment detects those signals and recovers the data for the onward network.

Modern systems can also use multiple optical wavelengths within a fiber. This is wavelength-division multiplexing: separate optical channels share the same physical medium.

NEC’s discussion of submarine monitoring describes the complexity created by managing those channels and branching connections. A cable system is therefore more than a single light source aimed through one piece of glass.

The equipment at the ends matters alongside the underwater cable. Improving terminal technology can make more effective use of a suitable installed system, although the cable’s design still sets constraints.

What do underwater repeaters do?

Light loses strength as it travels through fiber. Long systems include repeaters using optical amplification to support transmission across the ocean.

The amplification equipment needs energy. That is why a cable carrying information optically can still include electrical power feeding from shore.

Shorter links may use a different design and avoid the same arrangement of underwater amplification. There is no single repeater spacing or construction that should be assumed for every system.

ITU’s submarine-system guidance treats optical performance, electrical feeding and mechanical properties together. Those parts must work as one system throughout deployment and operation.

How are undersea cables laid?

Survey and choose the route

Planning begins before the cable reaches a ship. Engineers examine possible landing points, seabed conditions, hazards and the other activities using the sea.

A route survey helps test the assumptions from the initial study. The goal is a practical path that can be installed, protected and maintained, rather than simply the shortest straight line on a map.

Permissions and coordination also form part of the work. A route can cross jurisdictions and encounter existing cables, pipelines, fishing grounds or environmentally sensitive areas.

Manufacture, load and deploy

After the design is finalized, the cable and associated equipment are manufactured and loaded for installation. Specialized ships control how cable is released as they follow the planned route.

The cable must settle appropriately against the seabed’s shape. Handling tension and avoiding unsupported spans are part of the engineering, while tests help reveal damage during deployment.

Shore approaches can require separate vessels and techniques because the main cable ship cannot safely enter very shallow water. Installation is therefore a sequence of connected operations, rather than one uninterrupted spool dropped overboard.

Protect vulnerable sections

Where suitable, a sea plough or other equipment places the cable below the seabed. Burial helps reduce exposure to activities such as anchoring and bottom-contact fishing.

The method depends on sediments and conditions. Hard ground or crossings can require other protective measures, and a buried cable can later become exposed as the seabed changes.

The important distinction is location-specific protection. Much of the deep-ocean route rests on the seabed, while vulnerable approaches receive additional attention.

What causes submarine cables to fail?

ICPC estimates roughly 150–200 telecommunications cable faults globally each year. It attributes about 70–80% to accidental human activity, especially fishing and ships’ anchors.

Natural hazards and equipment problems are other causes. A single regional event can affect more than one system, making route diversity valuable as well as the number of connections.

A fault does not necessarily mean a complete international outage. Networks with suitable alternative routes and capacity can move traffic while repair work proceeds.

However, alternatives are not unlimited. Rerouting can increase delay or congestion, and places dependent on relatively few links face a different level of vulnerability.

How do ships repair a cable?

Operators first use monitoring and tests to narrow the fault’s location. A repair vessel then needs the appropriate spare cable and equipment before traveling to the site.

The damaged section is recovered for examination and replacement. Depending on conditions, recovery can involve grapnels or remotely operated equipment, followed by work on the cable aboard the ship.

Engineers remove damaged material and join in a suitable replacement length. Optical, electrical and mechanical properties all need to remain compatible with the existing system.

The repaired cable is tested and returned to the seabed. A vulnerable buried section may also need renewed protection, rather than being left exposed after the join.

ITU notes that deep-water repair can require extra cable length and sometimes additional equipment to accommodate the resulting optical loss. A repair is more involved than simply fastening two broken ends together.

Why does repair take time?

A ship must be available and able to reach the site. Weather, water depth, seabed conditions and the nature of the fault influence what work is possible.

The practical sequence includes locating the cable, recovering it, making reliable joints and testing the system. A rushed repair that creates another weakness would not restore dependable service.

Cable ships are specialized for these operations. For another perspective on maritime engineering, our guide to the world’s largest ships examines vessels designed around very different tasks.

What does this mean for everyday internet use?

An ocean cable is one part of a longer path that includes local networks, terrestrial links and data centers. It can carry many kinds of communication without a user knowing which route a particular session takes.

That helps explain why distance, capacity and routing all matter. Our internet-speed guide separates throughput from responsiveness.

The network’s history also involved separate layers of invention. Who invented the internet explains how shared protocols made independent networks communicate, while submarine cables provide physical paths between many of them.

The system works because optical transmission, marine engineering and network operation fit together. Its apparent invisibility from shore hides a continuing cycle of surveying, installation, monitoring, upgrades and repair.

Frequently asked questions

Are undersea cables electrical or optical?

Telecommunications data travels through optical fibers as light. Long systems also use electrical conductors to power underwater equipment, so light transmission and electrical power have different roles.

Are cables buried across the whole ocean?

No. Burial is used where conditions and risks justify it, especially on vulnerable approaches. Much deep-ocean cable rests directly on the seabed, and protection varies along the route.

Can one broken cable disconnect a country?

The effect depends on alternative routes and spare capacity. A well-connected network may reroute traffic, while a place dependent on limited links can experience a much greater disruption.

Why not replace cables with satellites?

Satellites are valuable for remote access and other applications, but they complement rather than simply replace high-capacity ocean fiber routes. The appropriate technology depends on the location, capacity needs and service requirements.

Do submarine cable maps show exact routes?

TeleGeography says its public map uses stylized paths rather than precise cable coordinates. It is useful for understanding connections and landing points, but should not be treated as a navigation chart.

Sources

  1. TeleGeography Submarine Cable FAQs
  2. ICPC Media Enquiries and Frequently Asked Questions
  3. ITU-T G Supplement 41: Design Guidelines for Optical Fibre Submarine Cable Systems
  4. ITU-T G.971: General Features of Optical Fibre Submarine Cable Systems
  5. KIS-ORCA: Cable Design
  6. KIS-ORCA: Installation Procedures and Methods
  7. KIS-ORCA: Cable Burial
  8. KIS-ORCA: Maintenance and Repair Operations
  9. NEC: Optical Submarine Cable Network Monitoring Equipment
  10. NEC: SJC2 Optical Submarine Cable in Operation

More in Culture